Datamax A-Class Mark II Návod k obsluze Strana 116
- Strana / 160
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
106 A-Class Mark II
General Resolutions (continued)
Problem Possible solution
Poor print quality:
Check the following possibilities:
• Check the Leveling Cam for correct adjustment (readjust if
necessary; see Section 5.3.1);
• Review the print quality controls (adjust if necessary; see Section
3.5);
• If using thermal transfer, check the media and ribbon compatibility
(use a recommended combination; see Section 7.2); or,
• Check for a dirty Printhead (clean it if necessary; see Section
5.6.1).
Skips labels when
printing:
Check the following possibilities:
• Calibrate the printer (see Section 3.4);
• Adjust the Media Sensor (see Section 3.2); or,
• If the label format is within 1/8 inch of the media’s edge, reduce or
move the format slightly away.
6.1.2 Warning and Fault Messages
The printer displays messages when the possibility of a problem or an actual fault occurs.
Depending upon the displayed message, find the possible action or solution in the tables
below.
Warning and Fault Messages do not appear when in Menu or Test mode.
Warning Messages
Displayed for about three seconds, Warning Messages assume a low priority and indicate
a pending change in printer configuration, or an operating condition that could lead to a
fault.
- Operator’s Manual 1
- Special Text Instructions 5
- Applicability 5
- Contents 7
- Overview 11
- 1.1.1 Standard Features 12
- 1.1.2 Optional Features 13
- Installing Printer Options 14
- Getting Started 15
- 2.1.1 Contents 16
- 2.2 Mounting Requirements 17
- Mounting Holes 17
- 8 A-Class Mark II 18
- A-Class Mark II 9 19
- 10 A-Class Mark II 20
- 2.3 Connecting to a Host 21
- A-Class Mark II 22
- Main Logic Card 23
- 14 A-Class Mark II 24
- 2.3.4 USB Port Connections 25
- 16 A-Class Mark II 26
- 2.5 Connecting Power 27
- 18 A-Class Mark II 28
- Setting up the Printer 29
- Media Guide 31
- Locking Post 32
- A-Class Mark II 23 33
- 3.3 Loading Ribbon 34
- A-Class Mark II 25 35
- 3.3.2 Left Hand Models 36
- 3.3.3 Removing Ribbon 37
- 3.4 Quick Calibration 38
- 3.5 Print Quality Controls 38
- Using the Control Panel 39
- PL Z PL BPL I 40
- 4.1.2 Keypad Functions 41
- 4.2 The System Menu 42
- 4.2.1 Media Settings 43
- 0 – 2.00 in.) 44
- A-Class Mark II 35 45
- Section 7 for label details 46
- A-Class Mark II 37 47
- 4.2.3 Printer Options 48
- A-Class Mark II 39 49
- 40 A-Class Mark II 50
- A-Class Mark II 41 51
- 42 A-Class Mark II 52
- A-Class Mark II 43 53
- 44 A-Class Mark II 54
- A-Class Mark II 45 55
- 4.2.4 System Settings 56
- A-Class Mark II 47 57
- 48 A-Class Mark II 58
- A-Class Mark II 49 59
- 50 A-Class Mark II 60
- A-Class Mark II 51 61
- 52 A-Class Mark II 62
- A-Class Mark II 53 63
- 54 A-Class Mark II 64
- A-Class Mark II 55 65
- 4.2.5 Communications 66
- A-Class Mark II 57 67
- 000.000.000.000 68
- A-Class Mark II 59 69
- 60 A-Class Mark II 70
- A-Class Mark II 61 71
- 62 A-Class Mark II 72
- A-Class Mark II 63 73
- 4.2.6 Diagnostics 74
- A-Class Mark II 65 75
- 66 A-Class Mark II 76
- 4.2.7 MCL Options 77
- 4.3 The Test Menu 78
- 4.3.3 Test Label 79
- 4.3.4 Validation Label 79
- 4.3.5 Print Configuration 79
- 4.3.6 Print Last Label 80
- 4.3.7 User-Defined Label 80
- Operating, Adjusting and 81
- Maintaining the Printer 81
- 72 A-Class Mark II 82
- A-Class Mark II 73 83
- 5.2 Calibration 84
- A-Class Mark II 75 85
- 5.2.2 Advanced Entry 86
- A-Class Mark II 88
- The re-sampled values may 91
- 82 A-Class Mark II 92
- 5.3 Printhead Adjustments 93
- Leveling Cam 94
- 5.3.2 Burn Line Adjustment 95
- 5.4 Printhead Replacement 96
- Printhead Assembly 97
- Access Cover 97
- 88 A-Class Mark II 98
- Platen Roller 99
- 5.6 Maintenance Schedule 100
- A-Class Mark II 91 101
- 92 A-Class Mark II 102
- 5.6.2 Cleaning the Rollers 103
- Peel Assembly 104
- Peel Assembly Release Lever 104
- Head Lift Lever 104
- Latch Roller 105
- Knurled Roller 105
- 96 A-Class Mark II 106
- 5.7 Reset Methods 107
- 5.8 Updating the Firmware 108
- A-Class Mark II 99 109
- 100 A-Class Mark II 110
- 5.10 Fonts 111
- 102 A-Class Mark II 112
- Troubleshooting 113
- 104 A-Class Mark II 114
- A-Class Mark II 105 115
- 106 A-Class Mark II 116
- A-Class Mark II 107 117
- 108 A-Class Mark II 118
- A-Class Mark II 109 119
- 110 A-Class Mark II 120
- A-Class Mark II 111 121
- When the SENSOR 122
- 6.2 Hex Dump Mode 123
- 114 A-Class Mark II 124
- Specifications 125
- Electrical 126
- Environmental 126
- Mechanical 126
- Printing 127
- 118 A-Class Mark II 128
- A-Class Mark II 119 129
- 120 A-Class Mark II 130
- A-Class Mark II 121 131
- 122 A-Class Mark II 132
- Appendix A 133
- File Handling Messages 134
- Cut Behind Setup 135
- 126 A-Class Mark II 136
- Appendix B 137
- 128 A-Class Mark II 138
- Appendix C 139
- 130 A-Class Mark II 140
- Appendix D 141
- 132 A-Class Mark II 142
- Pins 1 – 2 = +5VDC; 143
- Pins 2 – 3 = +24VDC; or 143
- None = A common external 143
- 134 A-Class Mark II 144
- A-Class Mark II 135 145
- 136 A-Class Mark II 146
- Signal Out 147
- Signal In 147
- GPIO SIGNAL INFO 148
- Appendix E 149
- 140 A-Class Mark II 150
- A-Class Mark II 141 151
- 142 A-Class Mark II 152
- Appendix F 153
- 144 A-Class Mark II 154
- Appendix G 155
- 146 A-Class Mark II 156
- Glossary 157
- 148 A-Class Mark II 158
- A-Class Mark II 149 159
Související produkty a manuály pro Čtečky čárových kódů Datamax A-Class Mark II
(4 stránky)
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce